Vissani QR027 Specifications download pdf (Page 10)

Pre-Installation (continued)

WIRING CONNECTION REQUIREMENTS

Installation work and electrical wiring must be done by a qualied

person(s) in accordance with all applicable codes and standards,

including re-rated construction.

OBSERVE ALL GOVERNING CODES AND ORDINANCES WARNINGS

- Electrical grounding is required for this range hood. Check

with a qualied electrician if you are not sure whether the

range hood is properly grounded.

- Failure to follow electrical requirements may result in a

re.

- A fuse in the neutral or grounding circuit could result in

electrical shock.

- If the hot/cold water pipe is interrupted by plastic

nonmetallic gaskets or other materials, DO NOT use for

grounding.

- DO NOT GROUND TO A GAS PIPE.

IMPORTANT: It is the customer’s responsibility to contact a qualied

electrical installer and assure that the electrical installation is

adequate and complies with the National Electrical Code, or CSA

standards, as well as all local codes and ordinances.

1. Save installation instructions for electrical inspector’s use.

2. If codes permit and a separate ground wire is used, it is

recommended that a qualied electrician determine if the

ground path is adequate.

3. DO NOT use an extension cord or adapter plug with this

appliance.

4. The range hood must be connected with copper wire only.

5. The range hood should be connected directly to the junction

(or circuit breaker) box through exible, armoured or

nonmetallic sheathed copper cable. Allow some slack in the

cable so the

appliance can be moved if servicing is ever necessary.

6. A UL listed or CSA approved conduit connector must be

provided at each end of the power supply cable (at the range

hood and at

the junction box).

7. When making the electrical connection, cut a 3.2 cm (1-1/4 in.

hole in the wall. A hole cut through wood must be sanded until

smooth. A hole through metal must have a grommet.

8. When cutting or drilling into the wall or ceilling, do not damage

electrical wiring and other hidden utilities.

9. Wire size must conform to all local codes and ordinances.

The latest edition requirements of the National Electrical Code

ANSI/NFPA 70, or the latest edition CSA Standards C22.1-94,

Canadian Electrical Code Part 1 and C22.2 No. 0-M91.

DANGER: Risk of electrical shock. This range hood

must be properly grounded.

DANGER: Turn off the power circuit breaker or the

power switch on the junction box before installing this

unit. Touching circuitry inside the range hood while it is

energized will result in death or serious injury.

DANGER: All electrical wiring must be properly installed,

insulated, and grounded. Improper insulation and grounding

will result in deadly electrical shock.

NOTE:

Temporarily wire the range hood to test it for proper operation. If

the range hood does not operate correctly, do not proceed with the

installation.

- Cut a 1 1/4 in. (31.75 cm) diameter hole in an appropriate

location in the wall for the electrical connection. A hole cut

through wood must be sanded until smooth. A hole through

metal must have a grommet.

- Connect the range hood (A) directly to the junction box or

circuit breaker box with a exible, armoured, or nonmetallic

sheathed copper cable. Allow some slack in the cable so

the appliance can be moved if servicing is ever necessary.

- Connect a UL-listed or CSA-approved conduit connector to

each end of the power supply cable (at the range hood and

at the junction box).

- Connect the three colored wires (6) from the range hood (A)

to the corresponding wires (7) from the electrical source:

black to black (live), white to white (neutral), and green to

green/yellow (ground). Cap wires with wire connectors.

- Turn the power on, and ensure that all lights and fans are

operating correctly.

- Once you have tested the electrical connection, disconnect

the power supply cable and wires from the electrical

source before proceeding with the rest of the installation.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 19 20

Comments to this Manuals

No comments

Vissani QR027 Specifications Page 10

Comments to this Manuals